Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Nighthawk X6S Tri-Band WiFi Range Extender
At a glance
ProductNETGEAR Nighthawk X6S Tri-Band WiFi Range Extender (EX8000)   [Website]
SummaryAC3000 class three-radio Wi-Fi range extender with 4 Gigabit Ethernet ports and USB 2.0 port supporting storage sharing.
Pros- 4x4 5 GHz high-band radio can be used for back or fronthaul
- Impressive extended throughput
Cons- Pricey
- Aesthetics

Typical Price: $180  Buy From Amazon

Introduction

When NETGEAR announced its EX8000 Nighthawk X6S Tri-Band WiFi Range Extender at the end of August, I dubbed it the "DIY Orbi Extender. Little did I know how accurate that description was for reasons I'll reveal shortly.

The EX8000 is the first three-radio/"tri-band" Wi-Fi extender to hit the market. Like the original RBK50 Orbi, the EX8000 combines a two-stream dual-band 802.11ac AC1300 class radio with a third, four-stream 5 GHz radio. Also like Orbi, the two-stream 5 GHz radio only operates in the 5 GHz low-band channels (36-48) and the four-stream only in the high-band channels (149-161).

NETGEAR EX8000 architecture

NETGEAR EX8000 architecture

But unlike Orbi, any of the three radios can be used to link back to the wireless router you're extending. Orbi always uses its 5 GHz high-band radio for backhaul, falling back to sharing the 2.4 GHz client-facing radio also for backhaul in the unlikely event it can't get a 5 GHz link.

However, the biggest difference between Orbi and the EX8000 is that Orbi will link only to other Orbis, while the EX8000 will connect to any router. Since the EX8000 also can be set to function as "tri-band" access point, you can even use a pair of them as a wireless bridge. A pair of EX8000's won't replace an Orbi, however, since it has no routing features.

The LED callouts show Link Status and "Maximum Throughput" indicators meant to communicate backhaul condition. It doesn't look like the two lights can tell you which 5 GHz radio is being used for backhaul. Of course, since that depends on the 5 GHz channel you set your main router to, you'd already know that.

NETGEAR EX8000 LED callouts

NETGEAR EX8000 LED callouts

The rear panel callouts show the four gigabit Ethernet ports and other ports and buttons. The USB 2.0 port supports Readyshare storage and printer sharing

NETGEAR EX8000 rear callouts

NETGEAR EX8000 rear callouts

The EX8000 is meant to sit on a shelf or table; it has no wall/ceiling mount screw slots.

Inside

NETGEAR requested short-term confidentiality on the EX8000's FCC internal photos, so I opened it up after testing was completed. I didn't have to go very far with disassembly because the innards looked very familiar.

NETGEAR EX8000 main board

NETGEAR EX8000 main board

If you compare the EX8000 photo above with the RBK50 Orbi photo below, it's obvious the two use the same main board. The differences I could detect are highlighted in the photo; 32 MB of flash replacing the 4 GB in Orbi and no Bluetooth radio. The top of the two products is also different, with different plastic brackets supporting the antennas and light-guides for the EX8000's onboard LEDs.

NETGEAR Orbi (RBK50) main board

NETGEAR Orbi (RBK50) main board

The table shows the key components of both.

  NETGEAR EX8000 NETGEAR Orbi RBK50
CPU Qualcomm IPQ4019 Qualcomm IPQ4019
Switch QCA8075 QCA8075
RAM 512 MB 512 MB
Flash 32 MB 4 GB
2.4 GHz Radio - In IPQ4019
- Skyworks SKY2623L 2.4 GHz Power Amp (x2)
- In IPQ4019
- Skyworks SKY2623L 2.4 GHz Power Amp (x2)
5 GHz radio - In IPQ4019
- RFMD RFPA5542 5 GHz power amp (x2)
- In IPQ4019
- RFMD RFPA5542 5 GHz power amp (x2)
5 GHz backhaul - QCA9984
- RFMD RFPA5542 5 GHz power amp (x4)
- QCA9984
- RFMD RFPA5542 5 GHz power amp (x4)
Bluetooth None CSR8811 Bluetooth 4.1 SoC
Table 1: NETGEAR EX8000 and RBK50 Orbi key components

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi,For many years I use a Raspberry Pi with Domoticz. And an Asus router RT-AC68U. In the router, I made a reservation for the IP-address for the RPi ...
Hey all.I have a ASUS AC68U router with Merlin's 384.7 and HP Photosmart 6510 all-in-one.I used to have no problems when scanning and printing with Li...
View attachment 14797​ Targeting the small office/home office crowd, QNAP’s 3-bay TS-351 is powered by an Intel Celeron J1800 dual-core 2.41 GHz proc...
Im looking for a new router to replace my basic Asus acrh13. I just switched from 3mbps dsl to a 100mbps cable internet connection for now & im also l...
I have used Networx network traffic monitor for a number of years and had no problems with it until I started using my RT-AC86U. Networx can either be...

Don't Miss These

  • 1
  • 2
  • 3